(440)462-0619
3 Flute Downcut Slow Spiral Roughers
Three flute slow spiral downcut roughers are designed to increase feed rates when surface finish is not important. Downcut
forces improve material hold down. These tools are recommended for plastic, natural wood and wood composites.
Shop by Category
- Ball Nose
- Chamfer Mills
- Chip Breakers
- Compression
- Diamond Tipped Bits
- Dovetail
- Edge Rounding Bits
- Engraving Bits
- Finishers
- Folding
- High Helix
- Low Helix
- MOAB-Plus Coated Solid Carbide Bits
-
O Flute
- O Flute Douncut Bit 1 Flute (General Purpose)
- O Flute Downcut 1 Flute Polished for Hard Plastics
- O Flute Downcut 1 Flute Polished for Soft Plastics
- O Flute High Helix Upcut Spiral 2 Flute
- O Flute Low Helix Upcut Spiral 2 Flute
- O Flute Rounding Edge Spiral Bit 1 Flute
- O Flute Rounding Edge Straight Flute 1 Flute
- O Flute Rounding Edge Straight Flute 2 Flute
- O Flute Slow Spirals
- O Flute Straight Bit 1 Flute Polished
- O Flute Straight Bit 1 Flute Polished-Left Hand
- O Flute Straight Bit 2 Flute Polished
- O Flute Upcut 1 Flute Polished for Hard Plastics
- O Flute Upcut 1 Flute Polished for Soft Plastics
- O Flute Upcut Bit 1 Flute (General Purpose)
- Pass-By
- Roughers
- Slot Cutters
-
Solid Carbide Bits
- 2 Flute Flush Trim Compression Bit
- 2 Flute Flush Trim Downcut Bit
- 2 Flute Flush Trim Upcut Bit
- 2 Flute Upcut Ball Nose
- Bevel Trim Bits
- Chamfer 2 + 2 Compression Bits
- Cove Nose Spiral Bit
- Dado Trim Bits
- Flat Bottom Veining Bits (2 Flute)
- Flush and Bevel Trim Bit
- Flush Trim Bit With Bearing
- Flush Trim Bits
- Hole and Flush Trim Bits
- Liner Bits
- Rip and Slotting Bits
- Round Bottom Veining Bits (1 Flute)
- Round Bottom Veining Bits (2 Flute)
- Solid Carbide Fiberglass Bits
- Solid Carbide Wood Screw Slot Bits
- Straight Bit 1 Flute (General Purpose Application)
- Straight Bit 2 Flute (General Purpose Application)
- Tapered Ball Nose - Upcut
- V-Grooving Bits
-
Solid Carbide Spiral Bits
- 1+1 Compression Bits
- 1+1 Compression Bits Left Hand
- 2 Flute Downcut Bits
- 2 Flute Downcut Bits HD
- 2 Flute Downcut Bits Left Hand
- 2 Flute Downcut Bits MD
- 2 Flute Downcut With Chipbreakers
- 2 Flute Upcut Bits
- 2 Flute Upcut Bits HD
- 2 Flute Upcut Bits Left Hand
- 2 flute Upcut Bits MD
- 2 Flute Upcut Bits With Chipbreakers
- 2+2 Compressions
- 2+2 Compressions HD
- 2+2 Compressions Left Hand
- 2+2 Compressions MD
- 2+2 Compressions MD Mortise
- 2+2 Compressions Mortise
- 2+2 Compressions with Chipbreakers
- 3 Flute Downcut Bits
- 3 Flute Downcut Bits with Chipbreakers
- 3 Flute Downcut Roughers
- 3 Flute Downcut Slow Spiral Roughers
- 3 Flute Downcut Slow Spirals
- 3 Flute Upcut Bits
- 3 Flute Upcut Bits with Chipbreakers
- 3 Flute Upcut Roughers
- 3 Flute Upcut Slow Spiral Bits
- 3 Flute Upcut Slow Spiral Roughers
- 3+3 Compression HD
- 3+3 Compressions
- 3+3 Compressions MD
- 4 Flute Downcut Finishing/Rougher
- 4 Flute Upcut Finishing/Rougher
- 4+4 Compressions
- 4+4 Finishing/Rougher Compressions
- Spoil Board Cutter
- Surfacing Bits
- V-Groove